Ramdisk???

[mandrake2217]

U-Boot 1.1.4 (Mar 15 2012 - 15:43:19) Marvell version: 3.4.4

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B43C

Soc: 88F6281 A1 (DDR2)
CPU running @ 0Mhz L2 running @ 0Mhz
SysClock = 0Mhz , TClock = 200Mhz

DRAM CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM CS[1] base 0x08000000 size 128MB
DRAM Total size 256MB 16bit width
[4096kB@f8000000] Flash: 4 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 1 is AUDIO

USB 0: host mode
PEX 0: interface detected no Link.

Synology Model: DS212jr1
Fan Status: Not Good
Fan 1: Not Good

Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Bad Magic Number
Marvell>>

what can i do?

meine printenv:

Marvell>> printenv
bootcmd=bootm F8080000 F8280000
baudrate=115200
loads_echo=0
ipaddr=192.168.101.224
serverip=192.168.101.111
rootpath=/mnt/ARM_FS/
netmask=255.255.0.0
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=cfi_flash:0x380000(root),0x80000(uboot)ro
mainlineLinux=no
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=1
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=::B88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
bootdelay=3
disaMvPnp=no
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2 :3),mtu=1500
usb0Mode=host
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212jv20 ihd_num=2 netif_num=1
ethact=egiga0
ethaddr=00:00:5f:ff:00:00
eth1addr=00:01:5f:ff:00:01

Environment size: 1098/4092 bytes

 

[Frogman]

Kannst Du auch in ganzen Sätzen schreiben, was Du uns sagen oder fragen willst?

 

[mandrake2217]

wie ich meine ds212j zum laufen bekomme :-(

sorry war gestern nur kurz angebunden ... ich versuche einfach meine ramdisk wieder hinzubekommen ... bisher bin ich soweit ...

Marvell>> setenv serverip 192.168.0.43
Marvell>> setenv ipaddr 192.168.0.60
Marvell>> tftpboot 0x1000000 zImage
Using egiga0 device
TFTP from server 192.168.0.43; our IP address is 192.168.0.60
Filename 'zImage'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
############################################
done
Bytes transferred = 1552216 (17af58 hex)
Marvell>> tftpboot 0x7000000 rd.bin
Using egiga0 device
TFTP from server 192.168.0.43; our IP address is 192.168.0.60
Filename 'rd.bin'.
Load address: 0x7000000
Loading: #################################################################
#################################################################
#################################################################
#######
done
Bytes transferred = 1030435 (fb923 hex)
Marvell>> sf probe 0 60000000
Usage:
sflash - read, write or erase the external SPI Flash.

Marvell>> bootm 0x1000000 0x7000000
## Booting image at 01000000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1552152 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 07000000 ...
Image Name: synology_88f6281_212j 8451
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1030371 Bytes = 1006.2 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #8451 Wed Aug 17 05:12:01 CST 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 21
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS212jv20 ihd_num=2 netif_num=1
[ 0.000000] Synology Hardware Version: DS212jv20-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 128MB 128MB = 256MB total
[ 0.000000] Memory: 244992KB available (3652K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1058.40 BogoMIPS (lpj=5292032)
[ 0.260000] Mount-cache hash table entries: 512
[ 0.260000] CPU: Testing write buffer coherency: ok
[ 0.260000] devtmpfs: initialized
[ 0.260000] xor: measuring software checksum speed
[ 0.310000] arm4regs : 965.200 MB/sec
[ 0.360000] 8regs : 579.200 MB/sec
[ 0.410000] 32regs : 747.600 MB/sec
[ 0.410000] xor: using function: arm4regs (965.200 MB/sec)
[ 0.410000] NET: Registered protocol family 16
[ 0.410000] Feroceon L2: Enabling L2
[ 0.410000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.420000]

 

[mandrake2217]

[ 0.420000] CPU Interface
[ 0.420000] -------------
[ 0.420000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.420000] SDRAM_CS1 ....base 08000000, size 128MB
[ 0.420000] SDRAM_CS2 ....disable
[ 0.420000] SDRAM_CS3 ....disable
[ 0.420000] PEX0_MEM ....base e0000000, size 128MB
[ 0.420000] PEX0_IO ....base f2000000, size 1MB
[ 0.420000] PEX1_MEM ....no such
[ 0.420000] PEX1_IO ....no such
[ 0.420000] INTER_REGS ....base f1000000, size 1MB
[ 0.420000] NFLASH_CS ....base fa000000, size 2MB
[ 0.420000] SPI_CS ....base f4000000, size 16MB
[ 0.420000] BOOT_ROM_CS ....no such
[ 0.420000] DEV_BOOTCS ....no such
[ 0.420000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.420000] Detected Tclk 200000000 and SysClk 0
[ 0.420000] Synology 6281 1, 2 bay GPIO Init
[ 0.920000] PEX0 interface detected no Link.
[ 0.920000] PCI: bus0: Fast back to back transfers enabled
[ 0.920000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[ 0.930000] bio: create slab <bio-0> at 0
[ 0.930000] vgaarb: loaded
[ 0.930000] SCSI subsystem initialized
[ 1.100000] raid6: int32x1 90 MB/s
[ 1.270000] raid6: int32x2 130 MB/s
[ 1.440000] raid6: int32x4 121 MB/s
[ 1.610000] raid6: int32x8 130 MB/s
[ 1.610000] raid6: using algorithm int32x8 (130 MB/s)
[ 1.610000] Switching to clocksource kw_clocksource
[ 1.610000] NET: Registered protocol family 2
[ 1.610000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.610000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.610000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.610000] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.610000] TCP reno registered
[ 1.610000] NET: Registered protocol family 1
[ 1.610000] RPC: Registered udp transport module.
[ 1.610000] RPC: Registered tcp transport module.
[ 1.610000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.610000] Trying to unpack rootfs image as initramfs...
[ 1.610000] Freeing initrd memory: 4096K
[ 1.610000] XOR registered 4 channels
[ 1.610000] XOR 2nd invalidate WA enabled
[ 1.610000] VFS: Disk quotas dquot_6.5.2
[ 1.610000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.610000] msgmni has been set to 486
[ 1.610000] alg: No test for md5 (md5-generic)
[ 1.610000] alg: No test for des (des-generic)
[ 1.610000] alg: No test for des3_ede (des3_ede-generic)
[ 1.610000] alg: No test for stdrng (krng)
[ 1.610000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 1.610000] io scheduler noop registered
[ 1.610000] io scheduler anticipatory registered (default)
[ 1.620000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.620000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 1.630000] console [ttyS0] enabled
[ 1.630000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 1.650000] brd: module loaded
[ 1.650000] sata_mv sata_mv.0: version 1.28
[ 1.650000] sata_mv sata_mv.0: slots 32 ports 2
[ 1.660000] scsi0 : sata_mv
[ 1.660000] scsi1 : sata_mv
[ 1.670000] ata1: SATA max UDMA/133 irq 21
[ 1.670000] ata2: SATA max UDMA/133 irq 21
[ 10.220000] ata1: link is slow to respond, please be patient (ready=0)
[ 14.420000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 14.480000] ata1.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
[ 14.480000] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 14.530000] ata1.00: configured for UDMA/133
[ 14.550000] scsi 0:0:0:0: Direct-Access WDC WD20EARS-00MVWB0 51.0 PQ: 0 ANSI: 5
[ 14.550000] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 14.560000] sd 0:0:0:0: [sda] Write Protect is off
[ 14.570000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 14.580000] sda: sda1
[ 14.600000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 17.590000] Delay 5 seconds to wait for disk 2 ready.
[ 28.140000] ata2: link is slow to respond, please be patient (ready=0)
[ 28.200000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 28.400000] ata2.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 28.400000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 28.450000] ata2.00: configured for UDMA/133
[ 28.470000] scsi 1:0:0:0: Direct-Access WDC WD20EARX-00PASB0 51.0 PQ: 0 ANSI: 5
[ 28.470000] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 28.480000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 28.490000] sd 1:0:0:0: [sdb] Write Protect is off
[ 28.490000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 28.500000] sdb: sdb1
[ 28.520000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 28.530000] physmap platform flash device: 00400000 at f8000000
[ 28.530000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 28.540000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 28.560000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 28.560000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 28.570000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 28.570000] 0x000000000000-0x000000080000 : "RedBoot"
[ 28.580000] 0x000000080000-0x000000280000 : "zImage"
[ 28.580000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 28.590000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 28.600000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 28.600000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 28.610000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 28.610000] serial number='CCKON03413'
[ 28.620000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 28.620000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 28.630000] mvCpuIfTargetWinBaseLowGet:ERR. Getting target 11 failed.
[ 28.640000] mvCpuIfTargetWinSizeGet:ERR. Getting target 11 failed.
[ 28.640000]
[ 28.640000] ERROR: flashInfoFill - Failed to get Device Base address and Size (spi_flash 0)Loading Marvell Ethernet Driver:
[ 28.660000] o Cached descriptors in DRAM
[ 28.660000] o DRAM SW cache-coherency
[ 28.660000] o 2 Giga ports supported
[ 28.670000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 28.670000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 28.680000] o TCP segmentation offload (TSO) supported
[ 28.680000] o Receive checksum offload supported
[ 28.690000] o Transmit checksum offload supported
[ 28.690000] o SKB Recycle supported - (Enabled)
[ 28.700000] o Rx descripors: q0=128
[ 28.700000] o Tx descripors: q0=532
[ 28.710000] o Loading network interface(s):
[ 28.710000] o register under mv88fx_eth platform
[ 28.720000] o eth0, ifindex = 2, GbE port = 0
[ 28.720000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 28.730000]
[ 28.730000] md: linear personality registered for level -1
[ 28.730000] md: raid0 personality registered for level 0
[ 28.740000] md: raid1 personality registered for level 1
[ 28.750000] md: raid10 personality registered for level 10
[ 28.750000] md: raid6 personality registered for level 6
[ 28.760000] md: raid5 personality registered for level 5
[ 28.760000] md: raid4 personality registered for level 4
[ 28.770000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 28.780000] cpuidle: using governor ladder
[ 28.780000] TCP cubic registered
[ 28.780000] NET: Registered protocol family 17
[ 28.790000] NET: Registered protocol family 15
[ 28.790000] registered taskstats version 1
[ 28.800000] md: Waiting for all devices to be available before autodetect
[ 28.800000] md: If you don't use raid, use raid=noautodetect
[ 28.810000] md: Autodetecting RAID arrays.
[ 28.810000] md: Scanned 0 and added 0 devices.
[ 28.820000] md: autorun ...
[ 28.820000] md: ... autorun DONE.
[ 28.830000] EXT3-fs: unable to read superblock
[ 28.830000] EXT2-fs: unable to read superblock
[ 28.830000] EXT4-fs (md0): unable to read superblock
[ 28.840000] List of all partitions:
[ 28.840000] 0800 1953514584 sda driver: sd
[ 28.850000] 0801 1953514583 sda1
[ 28.850000] 0810 1953514584 sdb driver: sd
[ 28.860000] 0811 1953514583 sdb1
[ 28.860000] 1f00 512 mtdblock0 (driver?)
[ 28.860000] 1f01 2048 mtdblock1 (driver?)
[ 28.870000] 1f02 1280 mtdblock2 (driver?)
[ 28.870000] 1f03 64 mtdblock3 (driver?)
[ 28.880000] 1f04 128 mtdblock4 (driver?)
[ 28.880000] 1f05 64 mtdblock5 (driver?)
[ 28.890000] No filesystem could mount root, tried: ext3 ext2 ext4
[ 28.900000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(9,0)

 

[mandrake2217]

... leider am ende mit einer kernel panic egal welche adressen ich nutze ...

 

[goetz]

Hallo,
probiere es mal mit den Adressen aus diesem Post.

Gruß Götz

PS: sf probe kannst Du weg lassen, das kennt Deine DS noch nicht in der Form.

 

[mandrake2217]

hatte geklappt ... und fast durchinstalliert, bis er connection verlor

per putty kommt nun das hier als letztes:

==================== start udevd ====================
[ 57.590000] NET: Registered protocol family 10
[ 57.590000] lo: Disabled Privacy Extensions
[ 57.660000] IPv6 over IPv4 tunneling driver
[ 57.670000] sit0: Disabled Privacy Extensions
[ 59.740000] init: syno-auth-check main process (1168) killed by TERM signal
[ 60.490000] <30>systemd-udevd[1264]: starting version 204
===== trigger device plug event =====
[ 64.530000] cpufreq: Init kirkwood cpufreq driver

 

[goetz]

Hallo,
sorry, da ist bei mir auch Ende angesagt. Du hast aber eine Version kleiner als ehemals installiert per tftp übertragen?

Gruß Götz

 

[mandrake2217]

damals war es eine ds214se ...nun aber die 2. ist eben eine ds212j.

keiner eine idee? wo es da hängt ...