DSM 6.x und darunter DS211 erkennt keine externen Geräte mehr

[Gatschi]

Hallo zusammen,

meine DS211 erkennt keine externen gerät mehr.

Das Problem habe ich schon über ein Jahr... Wenn ich Gerate (USB-HDD, USB-Stick, etc.) an einen der USB Ports anschließe, werden diese wohl initiiert aber nicht im DSM angezeigt. Soll heißen z.B. USB Festplatten starten wie immer (fangen an zu drehen und die LED leuchten) wie vorher als die Geräte noch korrekt erkannt wurden.
Aber im DSM wird nichts angezeigt. Ich habe mich auch mal per SSH verbunden aber auch dort werden auch nur die internen Platten angezeigt.

Habe die DS211 schon mehrmals komplett zurück gesetzt. Und auch andere DSM Versionen getestet.


B4H1N02...
Modellname
DS211
Prozessor
MARVELL Kirkwood 88F6282
Prozessor-Taktrate
1.6 GHz
Prozessorkerne
1
Arbeitsspeicher insgesamt
256 MB
DSM-Version
DSM 5.1-5022 Update 5

 

[Ameisentaetowierer]

Du hast dich per SSH angemeldet.
Wie hast du denn geschaut, ob die Platten angezeigt werden?

Sonst mach folgendes:
Per root über ssh anmelden.
Platte/Stick abziehen
"dmesg -c" eingeben und Enter drücken
Platte/Stick anstecken
10 Sekunden warten
"dmesg" eingeben und Enter drücken
Das Ergebnis hier posten

 

[Gatschi]

Hab ich gerade gemacht und mit einem Stick und einer Festplatte getestet.

Ergebnis von dmesg -c:

[ 0.000000] Linux version 2.6.32.12 (root@build8) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201309-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #5022 Wed Jan 7 14:19:44 CST 2015
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
...

Aber nach dem anstecken der Geräte kommt nach dmesg überhaupt keine Ausgabe.

Ich habe auch noch das AdminTool installiert. Kommen wir darüber weiter?
http://www.synology-wiki.de/index.php/AdminTool

 

[Gatschi]

DiskStation> dmesg -c
[ 0.000000] Linux version 2.6.32.12 (root@build8) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201309-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #5022 Wed Jan 7 14:19:44 CST 2015
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 23
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c03ed700, node_mem_map c0c01000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS211v10 ihd_num=2 netif_num=1
[ 0.000000] Synology Hardware Version: DS211v10-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 244992KB available (3628K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] devtmpfs: initialized
[ 0.240000] xor: measuring software checksum speed
[ 0.290000] arm4regs : 1448.400 MB/sec
[ 0.340000] 8regs : 869.200 MB/sec
[ 0.390000] 32regs : 1122.000 MB/sec
[ 0.390000] xor: using function: arm4regs (1448.400 MB/sec)
[ 0.390000] NET: Registered protocol family 16
[ 0.390000] Feroceon L2: Enabling L2
[ 0.390000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.410000]
[ 0.410000] CPU Interface
[ 0.410000] -------------
[ 0.410000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.410000] SDRAM_CS1 ....disable
[ 0.410000] SDRAM_CS2 ....disable
[ 0.410000] SDRAM_CS3 ....disable
[ 0.410000] PEX0_MEM ....base e0000000, size 128MB
[ 0.410000] PEX0_IO ....base f2000000, size 1MB
[ 0.410000] PEX1_MEM ....base e8000000, size 128MB
[ 0.410000] PEX1_IO ....base f2100000, size 1MB
[ 0.410000] INTER_REGS ....base f1000000, size 1MB
[ 0.410000] NFLASH_CS ....base fa000000, size 2MB
[ 0.410000] SPI_CS ....base f4000000, size 16MB
[ 0.410000] BOOT_ROM_CS ....no such
[ 0.410000] DEV_BOOTCS ....no such
[ 0.410000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.410000] Detected Tclk 200000000 and SysClk 533333333
[ 0.410000] Synology 6282 1, 2 bay GPIO Init
[ 0.910000] PEX0 interface detected no Link.
[ 1.410000] PEX1 interface detected no Link.
[ 1.410000] PCI: bus0: Fast back to back transfers enabled
[ 1.410000] PCI: bus1: Fast back to back transfers enabled
[ 1.420000] bio: create slab <bio-0> at 0
[ 1.420000] vgaarb: loaded
[ 1.420000] SCSI subsystem initialized
[ 1.420000] libata version 3.00 loaded.
[ 1.590000] raid6: int32x1 126 MB/s
[ 1.760000] raid6: int32x2 185 MB/s
[ 1.930000] raid6: int32x4 180 MB/s
[ 2.100000] raid6: int32x8 193 MB/s
[ 2.100000] raid6: using algorithm int32x8 (193 MB/s)
[ 2.100000] Switching to clocksource kw_clocksource
[ 2.100000] NET: Registered protocol family 2
[ 2.100000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.100000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 2.100000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 2.100000] TCP: Hash tables configured (established 8192 bind 8192)
[ 2.100000] TCP reno registered
[ 2.100000] NET: Registered protocol family 1
[ 2.100000] RPC: Registered udp transport module.
[ 2.100000] RPC: Registered tcp transport module.
[ 2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.100000] Trying to unpack rootfs image as initramfs...
[ 3.120000] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 3.130000] Freeing initrd memory: 4096K
[ 3.130000] XOR registered 4 channels
[ 3.130000] XOR 2nd invalidate WA enabled
[ 3.130000] VFS: Disk quotas dquot_6.5.2
[ 3.130000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.130000] msgmni has been set to 486
[ 3.130000] alg: No test for md5 (md5-generic)
[ 3.130000] alg: No test for des (des-generic)
[ 3.130000] alg: No test for des3_ede (des3_ede-generic)
[ 3.130000] alg: No test for stdrng (krng)
[ 3.130000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 3.130000] io scheduler noop registered
[ 3.130000] io scheduler anticipatory registered (default)
[ 3.140000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.140000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 3.150000] console [ttyS0] enabled
[ 3.150000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 3.160000] brd: module loaded
[ 3.170000] sata_mv sata_mv.0: version 1.28
[ 3.170000] sata_mv sata_mv.0: slots 32 ports 2
[ 3.180000] scsi0 : sata_mv
[ 3.180000] scsi1 : sata_mv
[ 3.180000] ata1: SATA max UDMA/133 irq 21
[ 3.190000] ata2: SATA max UDMA/133 irq 21
[ 8.740000] ata1: link is slow to respond, please be patient (ready=0)
[ 13.240000] ata1: SRST failed (errno=-16)
[ 13.240000] ata1: SRST fail, set srst fail flag
[ 14.110000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 14.110000] ata1: link reset sucessfully clear error flags
[ 14.140000] ata1.00: applying link speed limit horkage to 1.5 Gbps
[ 16.620000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl F310)
[ 16.660000] ata1.00: ATA-8: Hitachi HDS723020BLA642, MN6OA5C0, max UDMA/133
[ 16.660000] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 16.730000] ata1.00: configured for UDMA/133
[ 16.750000] scsi 0:0:0:0: Direct-Access Hitachi HDS723020BLA642 MN6O PQ: 0 ANSI: 5
[ 16.750000] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 16.760000] sd 0:0:0:0: [sda] Write Protect is off
[ 16.770000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

 

[Gatschi]

[ 16.770000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 16.780000] sda: sda1 sda2 sda3
[ 16.800000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 19.800000] Delay 5 seconds to wait for disk 2 ready.
[ 30.350000] ata2: link is slow to respond, please be patient (ready=0)
[ 34.850000] ata2: SRST failed (errno=-16)
[ 34.850000] ata2: SRST fail, set srst fail flag
[ 35.900000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 35.900000] ata2: link reset sucessfully clear error flags
[ 35.930000] ata2.00: applying link speed limit horkage to 1.5 Gbps
[ 38.410000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F310)
[ 38.450000] ata2.00: ATA-8: Hitachi HDS723020BLA642, MN6OA180, max UDMA/133
[ 38.450000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 38.520000] ata2.00: configured for UDMA/133
[ 38.540000] scsi 1:0:0:0: Direct-Access Hitachi HDS723020BLA642 MN6O PQ: 0 ANSI: 5
[ 38.540000] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 38.550000] sd 1:0:0:0: [sdb] Write Protect is off
[ 38.560000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 38.560000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 38.570000] sdb: sdb1 sdb2 sdb3
[ 38.580000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 38.580000] physmap platform flash device: 00400000 at f8000000
[ 38.590000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 38.590000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f0000
[ 38.610000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 38.610000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 38.620000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 38.620000] 0x000000000000-0x000000080000 : "RedBoot"
[ 38.630000] 0x000000080000-0x000000280000 : "zImage"
[ 38.640000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 38.640000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 38.650000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 38.650000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 38.660000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 38.670000] serial number='B4H1N02308'
[ 38.670000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 38.680000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 38.680000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 38.690000] cmdlinepart partition parsing not available
[ 38.700000] Loading Marvell Ethernet Driver:
[ 38.700000] o Cached descriptors in DRAM
[ 38.700000] o DRAM SW cache-coherency
[ 38.710000] o 2 Giga ports supported
[ 38.710000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 38.720000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 38.720000] o TCP segmentation offload (TSO) supported
[ 38.730000] o Receive checksum offload supported
[ 38.730000] o Transmit checksum offload supported
[ 38.740000] o SKB Recycle supported - (Enabled)
[ 38.740000] o Rx descripors: q0=128
[ 38.750000] o Tx descripors: q0=532
[ 38.750000] o Loading network interface(s):
[ 38.750000] o register under mv88fx_eth platform
[ 38.760000] o eth0, ifindex = 2, GbE port = 0
[ 38.760000] o eth0, phy chipid = 1410e40, Support WOL = 0
[ 38.770000]
[ 38.770000] md: linear personality registered for level -1
[ 38.780000] md: raid0 personality registered for level 0
[ 38.780000] md: raid1 personality registered for level 1
[ 38.790000] md: raid10 personality registered for level 10
[ 38.790000] md: raid6 personality registered for level 6
[ 38.800000] md: raid5 personality registered for level 5
[ 38.800000] md: raid4 personality registered for level 4
[ 38.810000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 38.820000] cpuidle: using governor ladder
[ 38.820000] TCP cubic registered
[ 38.830000] NET: Registered protocol family 17
[ 38.830000] NET: Registered protocol family 15
[ 38.840000] registered taskstats version 1
[ 38.840000] md: Waiting for all devices to be available before autodetect
[ 38.850000] md: If you don't use raid, use raid=noautodetect
[ 38.850000] md: Autodetecting RAID arrays.
[ 38.910000] md: invalid raid superblock magic on sda3
[ 38.910000] md: sda3 does not have a valid v0.90 superblock, not importing!
[ 38.960000] md: invalid raid superblock magic on sdb3
[ 38.970000] md: sdb3 does not have a valid v0.90 superblock, not importing!
[ 38.970000] md: Scanned 6 and added 4 devices.
[ 38.980000] md: autorun ...
[ 38.980000] md: considering sda1 ...
[ 38.980000] md: adding sda1 ...
[ 38.990000] md: sda2 has different UUID to sda1
[ 38.990000] md: adding sdb1 ...
[ 38.990000] md: sdb2 has different UUID to sda1
[ 39.000000] md: created md0
[ 39.000000] md: bind<sdb1>
[ 39.000000] md: bind<sda1>
[ 39.010000] md: running: <sda1><sdb1>
[ 39.010000] raid1: raid set md0 active with 2 out of 2 mirrors
[ 39.020000] md0: detected capacity change from 0 to 2549940224
[ 39.020000] md: considering sda2 ...
[ 39.030000] md: adding sda2 ...
[ 39.030000] md: adding sdb2 ...
[ 39.030000] md: created md1
[ 39.040000] md: bind<sdb2>
[ 39.040000] md: bind<sda2>
[ 39.040000] md: running: <sda2><sdb2>
[ 39.050000] raid1: raid set md1 active with 2 out of 2 mirrors
[ 39.050000] md1: detected capacity change from 0 to 2147418112
[ 39.060000] md: ... autorun DONE.

 

[Gatschi]

[ 39.060000] RAMDISK: lzma image found at block 0
[ 40.160000] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 40.330000] usbcore: registered new interface driver usbfs
[ 40.340000] usbcore: registered new interface driver hub
[ 40.340000] usbcore: registered new interface driver ethub
[ 40.370000] usbcore: registered new device driver usb
[ 40.400000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 40.460000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 40.460000] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 40.470000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 40.480000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 40.510000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 40.530000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 40.530000] usb usb1: configuration #1 chosen from 1 choice
[ 40.560000] hub 1-0:1.0: USB hub found
[ 40.560000] hub 1-0:1.0: 1 port detected
[ 40.720000] ds211_synobios: module license 'Synology Inc.' taints kernel.
[ 40.720000] Disabling lock debugging due to kernel taint
[ 40.750000] correction with 0x03
[ 40.850000] 2015-5-3 6:1:2 UTC
[ 40.850000] synobios: load, major number 201
[ 40.850000] Brand: Synology
[ 40.860000] Model: DS-211
[ 40.860000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 40.870000] synobios cpu_arch proc entry initialized
[ 40.870000] synobios crypto_hw proc entry initialized
[ 40.880000] synobios syno_platform proc entry initialized
[ 40.910000] synobios: unload
[ 40.990000] md0: unknown partition table
[ 42.510000] EXT4-fs (md0): barriers disabled
[ 42.530000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 44.970000] EXT3-fs: md0: couldn't mount because of unsupported optional features (240).
[ 44.970000] EXT2-fs: md0: couldn't mount because of unsupported optional features (240).
[ 44.990000] EXT4-fs (md0): barriers disabled
[ 44.990000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 45.000000] VFS: Mounted root (ext4 filesystem) on device 9:0.
[ 45.010000] Trying to move old root to /initrd ... okay
[ 45.020000] Freeing init memory: 124K
[ 47.570000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 47.570000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 47.980000] md1: unknown partition table
[ 48.050000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2097080k
[ 49.040000] init: syno-auth-check main process (857) killed by TERM signal
[ 49.750000] <30>systemd-udevd[973]: starting version 204
[ 49.950000] NET: Registered protocol family 10
[ 49.960000] lo: Disabled Privacy Extensions
[ 51.850000] IPv6 over IPv4 tunneling driver
[ 51.850000] sit0: Disabled Privacy Extensions
[ 54.670000] cpufreq: Init kirkwood cpufreq driver
[ 54.680000] cpufreq: High frequency: 1600000KHz - Low frequency: 533333KHz
[ 55.060000] alg: No test for aes (aes-generic)
[ 55.130000] alg: No test for stdrng (ansi_cprng)
[ 55.210000] alg: No test for crc32c (crc32c-generic)
[ 55.460000] cesadev_init(bf18d000)
[ 55.510000] mvCesaInit: sessions=10240, queue=64, pSram=f0000000
[ 55.600000] alg: No test for sha1 (sha1-generic)
[ 55.640000] alg: No test for sha224 (sha224-generic)
[ 55.640000] alg: No test for sha256 (sha256-generic)
[ 55.680000] alg: No test for sha384 (sha384-generic)
[ 55.680000] alg: No test for sha512 (sha512-generic)
[ 55.730000] encryptfs using the OCF package.
[ 56.110000] fuse init (API version 7.13)
[ 56.290000] sky2 driver version 1.25
[ 56.370000] correction with 0x03
[ 56.460000] 2015-5-3 6:1:18 UTC
[ 56.470000] synobios: load, major number 201
[ 56.470000] Brand: Synology
[ 56.470000] Model: DS-211
[ 56.480000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[ 56.480000] synobios cpu_arch proc entry initialized
[ 56.490000] synobios crypto_hw proc entry initialized
[ 56.490000] synobios syno_platform proc entry initialized
[ 57.470000] eth0: mac address changed
[ 59.550000] eth0: link down
[ 59.560000] eth0: started
[ 59.830000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 61.210000] eth0: link up, full duplex, speed 1 Gbps
[ 61.220000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 69.670000] md: md2 stopped.
[ 69.720000] md: bind<sdb3>
[ 69.810000] md: bind<sda3>
[ 69.810000] md2: detected capacity change from 0 to 3990922330112
[ 69.850000] md2: unknown partition table
[ 75.430000] EXT4-fs (md2): barriers disabled
[ 75.480000] EXT4-fs (md2): mounted filesystem with writeback data mode
[ 77.940000] Initializing USB Mass Storage driver...
[ 77.950000] usbcore: registered new interface driver usb-storage
[ 77.950000] USB Mass Storage support registered.
[ 78.110000] ata1.00: configured for UDMA/133
[ 78.110000] ata1: EH complete
[ 78.150000] ata2.00: configured for UDMA/133
[ 78.150000] ata2: EH complete
[ 78.160000] usbcore: registered new interface driver usblp
[ 78.570000] usbcore: registered new interface driver hiddev
[ 78.570000] usbcore: registered new interface driver usbhid
[ 78.580000] usbhid: v2.6:USB HID core driver
[ 82.830000] ata1.00: configured for UDMA/133
[ 82.830000] ata1: EH complete
[ 83.810000] ata2.00: configured for UDMA/133
[ 83.810000] ata2: EH complete
[ 91.570000] iSCSI: init_io_buffer_head(833) LUN-backup: 512 buffers allocated, total 2097152 bytes successfully
[ 95.250000] loop: module loaded
[ 95.930000] Slow work thread pool: Starting up
[ 96.360000] Slow work thread pool: Ready
[ 102.420000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[19374.170000] process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.
DiskStation>

 

[Ameisentaetowierer]

dmesg ist ein Kommando zur Anzeige der Kernelmeldungen der DS.
"dmesg -c" löscht alle aktuellen Meldungen, das macht nur die nachfolgenden Meldungen übersichtlicher
Wenn du ein Gerät anstöpselst, sollte der Kernel melden, dass er das mitbekommen hat und ein erneutes dmesg sollte was anzeigen.

Scheinbar hat deine DS aber nix mitbekommen....USB defekt?

Eine "korrekte" Anzeige (Kingston USB-Stick) sollte in etwa so aussehen:

[   65.018743] scsi 2:0:0:0: Direct-Access     Kingston DT 101 G2                PMAP PQ: 0 ANSI: 0 CCS
[   65.082427] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   65.888090] sd 2:0:0:0: [sdq] 31293440 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   65.912804] sd 2:0:0:0: [sdq] Write Protect is off
[   65.917632] sd 2:0:0:0: [sdq] Mode Sense: 03 41 00 00
[   65.932213] sd 2:0:0:0: [sdq] No Caching mode page present
[   65.937804] sd 2:0:0:0: [sdq] Assuming drive cache: write through
[   65.963314] sd 2:0:0:0: [sdq] No Caching mode page present
[   65.968838] sd 2:0:0:0: [sdq] Assuming drive cache: write through
[   65.994798]  sdq: sdq1
[   66.003500] sd 2:0:0:0: [sdq] No Caching mode page present
[   66.009031] sd 2:0:0:0: [sdq] Assuming drive cache: write through
[   66.015181] sd 2:0:0:0: [sdq] Attached SCSI removable disk

 

[Gatschi]

Ok, danke! Die Vermutung dass die USB Ports defekt sind hätte ich auch schon. Fand es nur merkwürdig dass die externen Festplatten anlaufen und auch die LED wie bei einem Zugriff blinken.

 

[Gatschi]

Mir ist noch was aufgefallen:

Müsste es im Ordner /usr/syno/etc/ nicht die Dateien usbdev.conf und usbno_guid.map geben?