Hallo zusammen,
meine DS212+ startet nicht mehr.
Die Status-Leuchte blinkt ständig orange und ich komme auch nicht mehr auf die Web-Oberfläche. Alles scheint tot zu sein.
Reset Button und ähnliches haben keine Abhilfe geschaffen.
Könnt Ihr mir weiterhelfen???
Die der UART-Auszug:
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Jul 19 2011 - 11:25:26) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1
Synology Model: DS212+
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1553660 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: synology_88f6282_212+ 25556
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 996943 Bytes = 973.6 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Apply DS212+ workaround
Apply DS212+ workaround done
Apply DS212+ workaround
Apply DS212+ workaround done
[ 0.000000] Linux version 2.6.32.12 (root@build8) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #25556 Tue Apr 11 11:08:47 CST 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397 7
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 27
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pa ges: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x0080004 0,4M root=/dev/md0 rw syno_hw_version=DS212pv10 ihd_num=2 netif_num=1 esata_7042 =1
[ 0.000000] Synology Hardware Version: DS212pv10-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] Esata chip use 7042: 1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 506880KB available (3656K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1985.74 BogoMIPS (lpj=9928704)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] devtmpfs: initialized
[ 0.250000] xor: measuring software checksum speed
[ 0.300000] arm4regs : 1810.800 MB/sec
[ 0.350000] 8regs : 1086.400 MB/sec
[ 0.400000] 32regs : 1402.400 MB/sec
[ 0.400000] xor: using function: arm4regs (1810.800 MB/sec)
[ 0.400000] NET: Registered protocol family 16
[ 0.400000] Feroceon L2: Enabling L2
[ 0.400000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.420000]
[ 0.420000] CPU Interface
[ 0.420000] -------------
[ 0.420000] SDRAM_CS0 ....base 00000000, size 512MB
[ 0.420000] SDRAM_CS1 ....disable
[ 0.420000] SDRAM_CS2 ....disable
[ 0.420000] SDRAM_CS3 ....disable
[ 0.420000] PEX0_MEM ....base e0000000, size 128MB
[ 0.420000] PEX0_IO ....base f2000000, size 1MB
[ 0.420000] PEX1_MEM ....base e8000000, size 128MB
[ 0.420000] PEX1_IO ....base f2100000, size 1MB
[ 0.420000] INTER_REGS ....base f1000000, size 1MB
[ 0.420000] NFLASH_CS ....base fa000000, size 2MB
[ 0.420000] SPI_CS ....base f4000000, size 16MB
[ 0.420000] BOOT_ROM_CS ....no such
[ 0.420000] DEV_BOOTCS ....no such
[ 0.420000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.420000] Detected Tclk 200000000 and SysClk 500000000
[ 0.420000] Apply DS 212 GPIO
[ 0.420000] Synology 6282 1, 2 bay GPIO Init
[ 0.420000] PCIe link is enable, apply PCIe workaround
[ 0.930000] PEX0 interface detected Link X4
[ 0.930000] PCIe link is enable, apply PCIe workaround
[ 1.430000] PEX1 interface detected Link X4
[ 1.430000] PCI: bus0: Fast back to back transfers disabled
[ 1.430000] pci 0000:01:01.0: PME# supported from D0 D3hot
[ 1.430000] pci 0000:01:01.0: PME# disabled
[ 1.430000] PCI: bus1: Fast back to back transfers disabled
[ 1.440000] bio: create slab <bio-0> at 0
[ 1.440000] vgaarb: loaded
[ 1.440000] SCSI subsystem initialized
[ 1.610000] raid6: int32x1 146 MB/s
[ 1.780000] raid6: int32x2 211 MB/s
[ 1.950000] raid6: int32x4 216 MB/s
[ 2.120000] raid6: int32x8 238 MB/s
[ 2.120000] raid6: using algorithm int32x8 (238 MB/s)
[ 2.120000] Switching to clocksource kw_clocksource
[ 2.120000] NET: Registered protocol family 2
[ 2.120000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 2.120000] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
[ 2.120000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 2.120000] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.120000] TCP reno registered
[ 2.120000] NET: Registered protocol family 1
[ 2.120000] RPC: Registered udp transport module.
[ 2.120000] RPC: Registered tcp transport module.
[ 2.120000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.120000] Trying to unpack rootfs image as initramfs...
[ 2.910000] rootfs image is not initramfs (no cpio magic); looks like an init rd
[ 2.920000] Freeing initrd memory: 4096K
[ 2.920000] XOR registered 4 channels
[ 2.920000] XOR 2nd invalidate WA enabled
[ 2.920000] VFS: Disk quotas dquot_6.5.2
[ 2.920000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.920000] msgmni has been set to 998
[ 2.920000] alg: No test for md5 (md5-generic)
[ 2.920000] alg: No test for des (des-generic)
[ 2.920000] alg: No test for des3_ede (des3_ede-generic)
[ 2.920000] alg: No test for stdrng (krng)
[ 2.920000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 2.920000] io scheduler noop registered
[ 2.920000] io scheduler anticipatory registered (default)
[ 2.930000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.930000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 2.940000] console [ttyS0] enabled
[ 2.940000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 2.950000] brd: module loaded
[ 2.950000] sata_mv sata_mv.0: version 1.28
[ 2.960000] sata_mv sata_mv.0: slots 32 ports 2
[ 2.960000] scsi0 : sata_mv
[ 2.970000] scsi1 : sata_mv
[ 2.970000] ata1: SATA max UDMA/133 irq 21
[ 2.970000] ata2: SATA max UDMA/133 irq 21
[ 11.520000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 11.560000] ata1.00: ATA-8: ST1000DM003-1SB10C, CC43, max UDMA/133
[ 11.560000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.630000] ata1.00: configured for UDMA/133
[ 11.650000] scsi 0:0:0:0: Direct-Access ATA ST1000DM003-1SB10C CC43 PQ: 0 ANSI: 5
[ 11.650000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/93 1 GiB)
[ 11.660000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 11.670000] sd 0:0:0:0: [sda] Write Protect is off
[ 11.670000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 11.680000] sda: sda1 sda2 sda3 < sda5 >
[ 11.710000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 14.710000] Delay 5 seconds to wait for disk 2 ready.
[ 25.260000] ata2: link is slow to respond, please be patient (ready=0)
[ 25.320000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 25.360000] ata2.00: ATA-8: ST1000DM003-1SB102, CC43, max UDMA/133
[ 25.360000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 25.430000] ata2.00: configured for UDMA/133
[ 25.450000] scsi 1:0:0:0: Direct-Access ATA ST1000DM003-1SB102 CC43 PQ: 0 ANSI: 5
[ 25.450000] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/93 1 GiB)
[ 25.460000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 25.470000] sd 1:0:0:0: [sdb] Write Protect is off
[ 25.470000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 25.480000] sdb: sdb1 sdb2 sdb3 < sdb5 >
[ 25.510000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 25.520000] sata_mv 0000:00:01.0: version 1.28
[ 25.520000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 25.530000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 25.540000] scsi2 : sata_mv
[ 25.540000] scsi3 : sata_mv
[ 25.540000] scsi4 : sata_mv
[ 25.550000] scsi5 : sata_mv
[ 25.550000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 25.560000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 25.570000] ata5: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 25.570000] ata6: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 25.930000] ata3: SATA link down (SStatus 0 SControl 300)
[ 26.280000] ata4: SATA link down (SStatus 0 SControl 300)
[ 26.630000] ata5: SATA link down (SStatus 0 SControl 300)
[ 26.980000] ata6: SATA link down (SStatus 0 SControl 300)
[ 26.980000] physmap platform flash device: 00400000 at f8000000
[ 26.990000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 27.000000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f 0000
[ 27.010000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 27.010000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 27.020000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 27.030000] 0x000000000000-0x000000080000 : "RedBoot"
[ 27.030000] 0x000000080000-0x000000280000 : "zImage"
[ 27.040000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 27.040000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 27.050000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.050000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.060000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.070000] serial number='BBKBN00948'
[ 27.070000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 27.080000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 27.080000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 27.090000] cmdlinepart partition parsing not available
[ 27.100000] Loading Marvell Ethernet Driver:
[ 27.100000] o Cached descriptors in DRAM
[ 27.110000] o DRAM SW cache-coherency
[ 27.110000] o 2 Giga ports supported
[ 27.110000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 27.120000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 27.120000] o TCP segmentation offload (TSO) supported
[ 27.130000] o Receive checksum offload supported
[ 27.130000] o Transmit checksum offload supported
[ 27.140000] o SKB Recycle supported - (Enabled)
[ 27.140000] o Rx descripors: q0=128
[ 27.150000] o Tx descripors: q0=532
[ 27.150000] o Loading network interface(s):
[ 27.160000] o register under mv88fx_eth platform
[ 27.160000] o eth0, ifindex = 2, GbE port = 0
[ 27.170000] o eth0, phy chipid = 1410e90, Support WOL = 32
[ 27.170000]
[ 27.170000] md: linear personality registered for level -1
[ 27.180000] md: raid0 personality registered for level 0
[ 27.180000] md: raid1 personality registered for level 1
[ 27.190000] md: raid10 personality registered for level 10
[ 27.200000] md: raid6 personality registered for level 6
[ 27.200000] md: raid5 personality registered for level 5
[ 27.210000] md: raid4 personality registered for level 4
[ 27.210000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-d evel@redhat.com
[ 27.220000] cpuidle: using governor ladder
[ 27.220000] TCP cubic registered
[ 27.230000] NET: Registered protocol family 17
[ 27.230000] NET: Registered protocol family 15
[ 27.240000] registered taskstats version 1
[ 27.240000] md: Waiting for all devices to be available before autodetect
[ 27.250000] md: If you don't use raid, use raid=noautodetect
[ 27.250000] md: Autodetecting RAID arrays.
[ 27.330000] md: invalid raid superblock magic on sda5
[ 27.330000] md: sda5 does not have a valid v0.90 superblock, not importing!
[ 27.390000] md: invalid raid superblock magic on sdb5
[ 27.400000] md: sdb5 does not have a valid v0.90 superblock, not importing!
[ 27.400000] md: Scanned 6 and added 4 devices.
[ 27.410000] md: autorun ...
[ 27.410000] md: considering sda1 ...
[ 27.420000] md: adding sda1 ...
[ 27.420000] md: sda2 has different UUID to sda1
[ 27.420000] md: adding sdb1 ...
[ 27.430000] md: sdb2 has different UUID to sda1
[ 27.430000] md: created md0
[ 27.430000] md: bind<sdb1>
[ 27.440000] md: bind<sda1>
[ 27.440000] md: running: <sda1><sdb1>
[ 27.440000] md: kicking non-fresh sdb1 from array!
[ 27.450000] md: unbind<sdb1>
[ 27.450000] md: export_rdev(sdb1)
[ 27.450000] raid1: raid set md0 active with 1 out of 2 mirrors
[ 27.460000] md0: detected capacity change from 0 to 2549940224
[ 27.470000] md: considering sda2 ...
[ 27.470000] md: adding sda2 ...
[ 27.470000] md: adding sdb2 ...
[ 27.480000] md: created md1
[ 27.480000] md: bind<sdb2>
[ 27.480000] md: bind<sda2>
[ 27.490000] md: running: <sda2><sdb2>
[ 27.490000] md: kicking non-fresh sdb2 from array!
[ 27.490000] md: unbind<sdb2>
[ 27.500000] md: export_rdev(sdb2)
[ 27.500000] raid1: raid set md1 active with 1 out of 2 mirrors
[ 27.510000] md1: detected capacity change from 0 to 2147418112
[ 27.510000] md: ... autorun DONE.
[ 27.520000] RAMDISK: lzma image found at block 0
[ 28.380000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[ 28.650000] usbcore: registered new interface driver usbfs
[ 28.650000] usbcore: registered new interface driver hub
[ 28.680000] usbcore: registered new interface driver ethub
[ 28.680000] usbcore: registered new device driver usb
... [ OK ]
:: Loading module ehci-hcd[ 28.750000] ehci_hcd: USB 2.0 'Enhanced' Host Contr oller (EHCI) Driver
[ 28.760000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 28.760000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num ber 1
[ 28.800000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 28.820000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 28.820000] usb usb1: configuration #1 chosen from 1 choice
[ 28.850000] hub 1-0:1.0: USB hub found
[ 28.850000] hub 1-0:1.0: 1 port detected
... [ OK ]
:: Loading module ohci-hcd[ 28.950000] ohci_hcd: USB 1.1 'Open' Host Controlle r (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd[ 28.990000] PCI: enabling device 0000:01:01.0 (0140 -> 0142)
[ 28.990000] xhci_hcd 0000:01:01.0: xHCI Host Controller
[ 29.000000] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus numbe r 2
[ 29.010000] xhci_hcd 0000:01:01.0: irq 10, io mem 0xe8000000
[ 29.020000] usb usb2: No SuperSpeed endpoint companion for config 1 interfac e 0 altsetting 0 ep 129: using minimum values
[ 29.040000] usb usb2: configuration #1 chosen from 1 choice
[ 29.070000] hub 2-0:1.0: USB hub found
[ 29.070000] hub 2-0:1.0: 4 ports detected
... [ OK ]
[ 29.170000] usb 1-1: new high speed USB device using orion-ehci and address 2
Insert net driver(Mindspeed only)...
[ 29.200000] ds212+_synobios: module license 'Synology Inc.' taints kernel.
[ 29.210000] Disabling lock debugging due to kernel taint
[ 29.270000] correction with 0x0f
[ 29.320000] 2066-4-6 23:53:18 UTC
[ 29.320000] synobios: load, major number 201
[ 29.330000] Brand: Synology
[ 29.330000] Model: DS-212+
[ 29.330000] This is default settings: set group disks wakeup number to 1, spi nup time deno 1
[ 29.340000] synobios cpu_arch proc entry initialized
[ 29.350000] synobios crypto_hw proc entry initialized
[ 29.350000] synobios syno_platform proc entry initialized
[ 29.360000] synobios open /dev/ttyS1 success
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[ 29.380000] synobios: unload
Partition Version=8
/sbin/e2fsck exists, checking /dev/md0...
[ 29.440000] md0:Got empty serial number. Generate serial number from product .
[ 29.450000] usb 1-1: configuration #1 chosen from 1 choice
[ 29.460000] unknown partition table
[ 29.470000] hub 1-1:1.0: USB hub found
[ 29.470000] hub 1-1:1.0: 4 ports detected
[ 29.760000] usb 1-1.4: new high speed USB device using orion-ehci and address 3
[ 29.890000] usb 1-1.4: configuration #1 chosen from 1 choice
/sbin/e2fsck -pvf returns 0
Mounting /dev/md0 /tmpRoot
[ 32.100000] EXT4-fs (md0): barriers disabled
[ 32.110000] EXT4-fs (md0): mounted filesystem with ordered data mode
------------upgrade
Begin upgrade procedure
No upgrade file exists
End upgrade procedure
============upgrade
Exit on error [2] .noroot exists...
Sat Mar 1 17:25:05 UTC 1930
/dev/md0 /tmpRoot ext4 rw,relatime,user_xattr,barrier=0,journal_checksum,data=or dered 0 0
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=253576k,nr_inodes=63394,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 2
starting pid 782, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
rc: Use all internal disk as swap.
/etc/rc: line 131: /usr/syno/bin/synodiskpathparse: not[ 32.610000] md1: foun d
/etc/rc: line 131: awk: not found
rc: Failed to parse partition sda2
unknown partition table
[ 32.630000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2 097080k
:: Loading module fat ... [ OK ]
:: Loading module vfat ... [ OK ]
:: Mounting usbfs ... [ OK ]
:: Loading module sky2[ 33.140000] sky2 driver version 1.25
... [ OK ]
:: Loading module synobios[ 33.240000] correction with 0x0f
[ 33.290000] 2066-4-6 23:53:22 UTC
[ 33.300000] synobios: load, major number 201
[ 33.300000] Brand: Synology
[ 33.310000] Model: DS-212+
[ 33.310000] This is default settings: set group disks wakeup number to 1, spi nup time deno 1
[ 33.320000] synobios cpu_arch proc entry initialized
[ 33.320000] synobios crypto_hw proc entry initialized
[ 33.330000] synobios syno_platform proc entry initialized
[ 33.330000] synobios open /dev/ttyS1 success
... [ OK ]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file [ 33.530000] eth0: mac address changed
or directory
[ 35.620000] eth0: link down
[ 35.620000] eth0: started
udhcpc (v1.16.1) started
eth0 Link encap:Ethernet HWaddr 00:11:32:0F:2F:E2
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[ 36.720000] eth0: link up, full duplex, speed 1 Gbps
:: Starting syslogd ... [ OK ]
/etc/rc: line 305: /usr/syno/bin/syno_pstore_collect: not found
:: Starting scemd
[ 43.010000] eth0: link down
[ 43.010000] eth0: link up, full duplex, speed 1 Gbps
:: Starting services in background
Starting findhostd in flash_rd...
Starting services in flash_rd...
Running /usr/syno/etc/rc.d/J30DisableNCQ.sh...
Disable ST1000DM003 NCQ
[ 43.240000] EXT4-fs (md0): barriers disabled
[ 43.260000] EXT4-fs (md0): mounted filesystem with ordered data mode
Disable ST1000DM003 NCQ
Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
:: Loading module usb-storage[ 43.630000] Initializing USB Mass Storage driver ...
[ 43.630000] scsi6 : SCSI emulation for USB Mass Storage devices
[ 43.660000] usbcore: registered new interface driver usb-storage
[ 43.660000] USB Mass Storage support registered.
... [ OK ]
============ Date ============
Sat Mar 1 17:25:16 UTC 1930
==============================
starting pid 1757, tty '': '/sbin/getty 115200 console'
Sat Mar 1 17:25:17 1930
DiskStation login: [ 46.090000] EXT4-fs (md0): barriers disabled
[ 46.110000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 46.240000] EXT4-fs (md0): barriers disabled
[ 46.260000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 48.700000] scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 48.710000] scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 48.750000] sd 6:0:0:0: [sdq] Attached SCSI removable disk
[ 48.820000] sd 6:0:0:1: [sdr] Attached SCSI removable disk
[ 110.380000] synobios: power button pressed, ret = 0
[ 111.640000] EXT4-fs (md0): barriers disabled
[ 111.650000] EXT4-fs (md0): mounted filesystem with ordered data mode
The system is going down NOW!
Sent SIGKILL to[ 112.820000] md: md0 in immediate safe mode
all processes
[ 112.820000] md: md1 in immediate safe mode
Unmounting all file systems.
Unmounting /proc/bus/usb ...
Unmounting /sys ...
Unmounting /dev/pts ...
Unmounting /dev ...
Failed to umount /dev, 16
Unmounting /tmp ...
Unmounting / ...
Unmounting / ...
All file systems unmounted.
rmmod usb_stora[ 117.890000] usbcore: deregistering interface driver usb-storag e
ge
Requesting system poweroff
[ 122.040000] md: stopping all md devices.
[ 122.040000] md: md1 switched to read-only mode.
[ 122.070000] md: md0 switched to read-only mode.
[ 123.070000] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 123.100000] sd 1:0:0:0: [sdb] Stopping disk
[ 123.460000] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 123.480000] sd 0:0:0:0: [sda] Stopping disk
[ 124.090000] xhci_thread. exit!
[ 124.100000] Power down.
[ 124.110000] eth0: link down
[ 124.110000] eth0: link up, full duplex, speed 1 Gbps
[ 124.120000] eth0: link up, half duplex, s
meine DS212+ startet nicht mehr.
Die Status-Leuchte blinkt ständig orange und ich komme auch nicht mehr auf die Web-Oberfläche. Alles scheint tot zu sein.
Reset Button und ähnliches haben keine Abhilfe geschaffen.
Könnt Ihr mir weiterhelfen???
Die der UART-Auszug:
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Jul 19 2011 - 11:25:26) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4
Soc: 88F6282 A1CPU running @ 2000Mhz L2 running @ 500Mhz
SysClock = 500Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
[4096kB@f8000000] Flash: 4 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: PCI Express Root Complex Interface
PEX interface detected Link X1
Synology Model: DS212+
Fan Status: Good
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
## Booting image at f8080000 ...
Image Name: Linux-2.6.32.12
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1553660 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: synology_88f6282_212+ 25556
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 996943 Bytes = 973.6 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Apply DS212+ workaround
Apply DS212+ workaround done
Apply DS212+ workaround
Apply DS212+ workaround done
[ 0.000000] Linux version 2.6.32.12 (root@build8) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #25556 Tue Apr 11 11:08:47 CST 2023
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397 7
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Synology 6282 board
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Sys Clk = 200000000, Tclk = 166666667
[ 0.000000] Synology Board ID: 27
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pa ges: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x0080004 0,4M root=/dev/md0 rw syno_hw_version=DS212pv10 ihd_num=2 netif_num=1 esata_7042 =1
[ 0.000000] Synology Hardware Version: DS212pv10-j
[ 0.000000] Internal HD num: 2
[ 0.000000] Internal netif num: 1
[ 0.000000] Esata chip use 7042: 1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 506880KB available (3656K code, 519K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1985.74 BogoMIPS (lpj=9928704)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] devtmpfs: initialized
[ 0.250000] xor: measuring software checksum speed
[ 0.300000] arm4regs : 1810.800 MB/sec
[ 0.350000] 8regs : 1086.400 MB/sec
[ 0.400000] 32regs : 1402.400 MB/sec
[ 0.400000] xor: using function: arm4regs (1810.800 MB/sec)
[ 0.400000] NET: Registered protocol family 16
[ 0.400000] Feroceon L2: Enabling L2
[ 0.400000] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.420000]
[ 0.420000] CPU Interface
[ 0.420000] -------------
[ 0.420000] SDRAM_CS0 ....base 00000000, size 512MB
[ 0.420000] SDRAM_CS1 ....disable
[ 0.420000] SDRAM_CS2 ....disable
[ 0.420000] SDRAM_CS3 ....disable
[ 0.420000] PEX0_MEM ....base e0000000, size 128MB
[ 0.420000] PEX0_IO ....base f2000000, size 1MB
[ 0.420000] PEX1_MEM ....base e8000000, size 128MB
[ 0.420000] PEX1_IO ....base f2100000, size 1MB
[ 0.420000] INTER_REGS ....base f1000000, size 1MB
[ 0.420000] NFLASH_CS ....base fa000000, size 2MB
[ 0.420000] SPI_CS ....base f4000000, size 16MB
[ 0.420000] BOOT_ROM_CS ....no such
[ 0.420000] DEV_BOOTCS ....no such
[ 0.420000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.420000] Detected Tclk 200000000 and SysClk 500000000
[ 0.420000] Apply DS 212 GPIO
[ 0.420000] Synology 6282 1, 2 bay GPIO Init
[ 0.420000] PCIe link is enable, apply PCIe workaround
[ 0.930000] PEX0 interface detected Link X4
[ 0.930000] PCIe link is enable, apply PCIe workaround
[ 1.430000] PEX1 interface detected Link X4
[ 1.430000] PCI: bus0: Fast back to back transfers disabled
[ 1.430000] pci 0000:01:01.0: PME# supported from D0 D3hot
[ 1.430000] pci 0000:01:01.0: PME# disabled
[ 1.430000] PCI: bus1: Fast back to back transfers disabled
[ 1.440000] bio: create slab <bio-0> at 0
[ 1.440000] vgaarb: loaded
[ 1.440000] SCSI subsystem initialized
[ 1.610000] raid6: int32x1 146 MB/s
[ 1.780000] raid6: int32x2 211 MB/s
[ 1.950000] raid6: int32x4 216 MB/s
[ 2.120000] raid6: int32x8 238 MB/s
[ 2.120000] raid6: using algorithm int32x8 (238 MB/s)
[ 2.120000] Switching to clocksource kw_clocksource
[ 2.120000] NET: Registered protocol family 2
[ 2.120000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 2.120000] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
[ 2.120000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 2.120000] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.120000] TCP reno registered
[ 2.120000] NET: Registered protocol family 1
[ 2.120000] RPC: Registered udp transport module.
[ 2.120000] RPC: Registered tcp transport module.
[ 2.120000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.120000] Trying to unpack rootfs image as initramfs...
[ 2.910000] rootfs image is not initramfs (no cpio magic); looks like an init rd
[ 2.920000] Freeing initrd memory: 4096K
[ 2.920000] XOR registered 4 channels
[ 2.920000] XOR 2nd invalidate WA enabled
[ 2.920000] VFS: Disk quotas dquot_6.5.2
[ 2.920000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.920000] msgmni has been set to 998
[ 2.920000] alg: No test for md5 (md5-generic)
[ 2.920000] alg: No test for des (des-generic)
[ 2.920000] alg: No test for des3_ede (des3_ede-generic)
[ 2.920000] alg: No test for stdrng (krng)
[ 2.920000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54)
[ 2.920000] io scheduler noop registered
[ 2.920000] io scheduler anticipatory registered (default)
[ 2.930000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.930000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 2.940000] console [ttyS0] enabled
[ 2.940000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 2.950000] brd: module loaded
[ 2.950000] sata_mv sata_mv.0: version 1.28
[ 2.960000] sata_mv sata_mv.0: slots 32 ports 2
[ 2.960000] scsi0 : sata_mv
[ 2.970000] scsi1 : sata_mv
[ 2.970000] ata1: SATA max UDMA/133 irq 21
[ 2.970000] ata2: SATA max UDMA/133 irq 21
[ 11.520000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 11.560000] ata1.00: ATA-8: ST1000DM003-1SB10C, CC43, max UDMA/133
[ 11.560000] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.630000] ata1.00: configured for UDMA/133
[ 11.650000] scsi 0:0:0:0: Direct-Access ATA ST1000DM003-1SB10C CC43 PQ: 0 ANSI: 5
[ 11.650000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/93 1 GiB)
[ 11.660000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 11.670000] sd 0:0:0:0: [sda] Write Protect is off
[ 11.670000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 11.680000] sda: sda1 sda2 sda3 < sda5 >
[ 11.710000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 14.710000] Delay 5 seconds to wait for disk 2 ready.
[ 25.260000] ata2: link is slow to respond, please be patient (ready=0)
[ 25.320000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 25.360000] ata2.00: ATA-8: ST1000DM003-1SB102, CC43, max UDMA/133
[ 25.360000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 25.430000] ata2.00: configured for UDMA/133
[ 25.450000] scsi 1:0:0:0: Direct-Access ATA ST1000DM003-1SB102 CC43 PQ: 0 ANSI: 5
[ 25.450000] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/93 1 GiB)
[ 25.460000] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 25.470000] sd 1:0:0:0: [sdb] Write Protect is off
[ 25.470000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, does n't support DPO or FUA
[ 25.480000] sdb: sdb1 sdb2 sdb3 < sdb5 >
[ 25.510000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 25.520000] sata_mv 0000:00:01.0: version 1.28
[ 25.520000] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 25.530000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 25.540000] scsi2 : sata_mv
[ 25.540000] scsi3 : sata_mv
[ 25.540000] scsi4 : sata_mv
[ 25.550000] scsi5 : sata_mv
[ 25.550000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 25.560000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 25.570000] ata5: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 25.570000] ata6: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 25.930000] ata3: SATA link down (SStatus 0 SControl 300)
[ 26.280000] ata4: SATA link down (SStatus 0 SControl 300)
[ 26.630000] ata5: SATA link down (SStatus 0 SControl 300)
[ 26.980000] ata6: SATA link down (SStatus 0 SControl 300)
[ 26.980000] physmap platform flash device: 00400000 at f8000000
[ 26.990000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB)
[ 27.000000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f 0000
[ 27.010000] 6 RedBoot partitions found on MTD device SYNOMTD-0
[ 27.010000] SYNOMTD flash bank 0: Using RedBoot partition definition
[ 27.020000] Creating 6 MTD partitions on "SYNOMTD-0":
[ 27.030000] 0x000000000000-0x000000080000 : "RedBoot"
[ 27.030000] 0x000000080000-0x000000280000 : "zImage"
[ 27.040000] 0x000000280000-0x0000003c0000 : "rd.gz"
[ 27.040000] 0x0000003c0000-0x0000003d0000 : "vendor"
[ 27.050000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.050000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.060000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[ 27.070000] serial number='BBKBN00948'
[ 27.070000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config"
[ 27.080000] 0x0000003f0000-0x000000400000 : "FIS directory"
[ 27.080000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB)
[ 27.090000] cmdlinepart partition parsing not available
[ 27.100000] Loading Marvell Ethernet Driver:
[ 27.100000] o Cached descriptors in DRAM
[ 27.110000] o DRAM SW cache-coherency
[ 27.110000] o 2 Giga ports supported
[ 27.110000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 27.120000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 27.120000] o TCP segmentation offload (TSO) supported
[ 27.130000] o Receive checksum offload supported
[ 27.130000] o Transmit checksum offload supported
[ 27.140000] o SKB Recycle supported - (Enabled)
[ 27.140000] o Rx descripors: q0=128
[ 27.150000] o Tx descripors: q0=532
[ 27.150000] o Loading network interface(s):
[ 27.160000] o register under mv88fx_eth platform
[ 27.160000] o eth0, ifindex = 2, GbE port = 0
[ 27.170000] o eth0, phy chipid = 1410e90, Support WOL = 32
[ 27.170000]
[ 27.170000] md: linear personality registered for level -1
[ 27.180000] md: raid0 personality registered for level 0
[ 27.180000] md: raid1 personality registered for level 1
[ 27.190000] md: raid10 personality registered for level 10
[ 27.200000] md: raid6 personality registered for level 6
[ 27.200000] md: raid5 personality registered for level 5
[ 27.210000] md: raid4 personality registered for level 4
[ 27.210000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-d evel@redhat.com
[ 27.220000] cpuidle: using governor ladder
[ 27.220000] TCP cubic registered
[ 27.230000] NET: Registered protocol family 17
[ 27.230000] NET: Registered protocol family 15
[ 27.240000] registered taskstats version 1
[ 27.240000] md: Waiting for all devices to be available before autodetect
[ 27.250000] md: If you don't use raid, use raid=noautodetect
[ 27.250000] md: Autodetecting RAID arrays.
[ 27.330000] md: invalid raid superblock magic on sda5
[ 27.330000] md: sda5 does not have a valid v0.90 superblock, not importing!
[ 27.390000] md: invalid raid superblock magic on sdb5
[ 27.400000] md: sdb5 does not have a valid v0.90 superblock, not importing!
[ 27.400000] md: Scanned 6 and added 4 devices.
[ 27.410000] md: autorun ...
[ 27.410000] md: considering sda1 ...
[ 27.420000] md: adding sda1 ...
[ 27.420000] md: sda2 has different UUID to sda1
[ 27.420000] md: adding sdb1 ...
[ 27.430000] md: sdb2 has different UUID to sda1
[ 27.430000] md: created md0
[ 27.430000] md: bind<sdb1>
[ 27.440000] md: bind<sda1>
[ 27.440000] md: running: <sda1><sdb1>
[ 27.440000] md: kicking non-fresh sdb1 from array!
[ 27.450000] md: unbind<sdb1>
[ 27.450000] md: export_rdev(sdb1)
[ 27.450000] raid1: raid set md0 active with 1 out of 2 mirrors
[ 27.460000] md0: detected capacity change from 0 to 2549940224
[ 27.470000] md: considering sda2 ...
[ 27.470000] md: adding sda2 ...
[ 27.470000] md: adding sdb2 ...
[ 27.480000] md: created md1
[ 27.480000] md: bind<sdb2>
[ 27.480000] md: bind<sda2>
[ 27.490000] md: running: <sda2><sdb2>
[ 27.490000] md: kicking non-fresh sdb2 from array!
[ 27.490000] md: unbind<sdb2>
[ 27.500000] md: export_rdev(sdb2)
[ 27.500000] raid1: raid set md1 active with 1 out of 2 mirrors
[ 27.510000] md1: detected capacity change from 0 to 2147418112
[ 27.510000] md: ... autorun DONE.
[ 27.520000] RAMDISK: lzma image found at block 0
[ 28.380000] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
Insert basic USB modules...
:: Loading module usbcore[ 28.650000] usbcore: registered new interface driver usbfs
[ 28.650000] usbcore: registered new interface driver hub
[ 28.680000] usbcore: registered new interface driver ethub
[ 28.680000] usbcore: registered new device driver usb
... [ OK ]
:: Loading module ehci-hcd[ 28.750000] ehci_hcd: USB 2.0 'Enhanced' Host Contr oller (EHCI) Driver
[ 28.760000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 28.760000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num ber 1
[ 28.800000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 28.820000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 28.820000] usb usb1: configuration #1 chosen from 1 choice
[ 28.850000] hub 1-0:1.0: USB hub found
[ 28.850000] hub 1-0:1.0: 1 port detected
... [ OK ]
:: Loading module ohci-hcd[ 28.950000] ohci_hcd: USB 1.1 'Open' Host Controlle r (OHCI) Driver
... [ OK ]
:: Loading module xhci-hcd[ 28.990000] PCI: enabling device 0000:01:01.0 (0140 -> 0142)
[ 28.990000] xhci_hcd 0000:01:01.0: xHCI Host Controller
[ 29.000000] xhci_hcd 0000:01:01.0: new USB bus registered, assigned bus numbe r 2
[ 29.010000] xhci_hcd 0000:01:01.0: irq 10, io mem 0xe8000000
[ 29.020000] usb usb2: No SuperSpeed endpoint companion for config 1 interfac e 0 altsetting 0 ep 129: using minimum values
[ 29.040000] usb usb2: configuration #1 chosen from 1 choice
[ 29.070000] hub 2-0:1.0: USB hub found
[ 29.070000] hub 2-0:1.0: 4 ports detected
... [ OK ]
[ 29.170000] usb 1-1: new high speed USB device using orion-ehci and address 2
Insert net driver(Mindspeed only)...
[ 29.200000] ds212+_synobios: module license 'Synology Inc.' taints kernel.
[ 29.210000] Disabling lock debugging due to kernel taint
[ 29.270000] correction with 0x0f
[ 29.320000] 2066-4-6 23:53:18 UTC
[ 29.320000] synobios: load, major number 201
[ 29.330000] Brand: Synology
[ 29.330000] Model: DS-212+
[ 29.330000] This is default settings: set group disks wakeup number to 1, spi nup time deno 1
[ 29.340000] synobios cpu_arch proc entry initialized
[ 29.350000] synobios crypto_hw proc entry initialized
[ 29.350000] synobios syno_platform proc entry initialized
[ 29.360000] synobios open /dev/ttyS1 success
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[ 29.380000] synobios: unload
Partition Version=8
/sbin/e2fsck exists, checking /dev/md0...
[ 29.440000] md0:Got empty serial number. Generate serial number from product .
[ 29.450000] usb 1-1: configuration #1 chosen from 1 choice
[ 29.460000] unknown partition table
[ 29.470000] hub 1-1:1.0: USB hub found
[ 29.470000] hub 1-1:1.0: 4 ports detected
[ 29.760000] usb 1-1.4: new high speed USB device using orion-ehci and address 3
[ 29.890000] usb 1-1.4: configuration #1 chosen from 1 choice
/sbin/e2fsck -pvf returns 0
Mounting /dev/md0 /tmpRoot
[ 32.100000] EXT4-fs (md0): barriers disabled
[ 32.110000] EXT4-fs (md0): mounted filesystem with ordered data mode
------------upgrade
Begin upgrade procedure
No upgrade file exists
End upgrade procedure
============upgrade
Exit on error [2] .noroot exists...
Sat Mar 1 17:25:05 UTC 1930
/dev/md0 /tmpRoot ext4 rw,relatime,user_xattr,barrier=0,journal_checksum,data=or dered 0 0
sys /sys sysfs rw,relatime 0 0
/dev/root.old / ext2 rw,relatime,errors=continue,user_xattr 0 0
none /dev devtmpfs rw,relatime,size=253576k,nr_inodes=63394,mode=755 0 0
proc /proc proc rw,relatime 0 0
linuxrc.syno failed on 2
starting pid 782, tty '': '/etc/rc'
:: Starting /etc/rc
:: Mounting procfs ... [ OK ]
:: Mounting tmpfs ... [ OK ]
:: Mounting devtmpfs ... [ OK ]
:: Mounting devpts ... [ OK ]
:: Mounting sysfs ... [ OK ]
rc: Use all internal disk as swap.
/etc/rc: line 131: /usr/syno/bin/synodiskpathparse: not[ 32.610000] md1: foun d
/etc/rc: line 131: awk: not found
rc: Failed to parse partition sda2
unknown partition table
[ 32.630000] Adding 2097080k swap on /dev/md1. Priority:-1 extents:1 across:2 097080k
:: Loading module fat ... [ OK ]
:: Loading module vfat ... [ OK ]
:: Mounting usbfs ... [ OK ]
:: Loading module sky2[ 33.140000] sky2 driver version 1.25
... [ OK ]
:: Loading module synobios[ 33.240000] correction with 0x0f
[ 33.290000] 2066-4-6 23:53:22 UTC
[ 33.300000] synobios: load, major number 201
[ 33.300000] Brand: Synology
[ 33.310000] Model: DS-212+
[ 33.310000] This is default settings: set group disks wakeup number to 1, spi nup time deno 1
[ 33.320000] synobios cpu_arch proc entry initialized
[ 33.320000] synobios crypto_hw proc entry initialized
[ 33.330000] synobios syno_platform proc entry initialized
[ 33.330000] synobios open /dev/ttyS1 success
... [ OK ]
cat: can't open '/proc/sys/kernel/syno_skip_vender_mac_interfaces': No such file [ 33.530000] eth0: mac address changed
or directory
[ 35.620000] eth0: link down
[ 35.620000] eth0: started
udhcpc (v1.16.1) started
eth0 Link encap:Ethernet HWaddr 00:11:32:0F:2F:E2
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[ 36.720000] eth0: link up, full duplex, speed 1 Gbps
:: Starting syslogd ... [ OK ]
/etc/rc: line 305: /usr/syno/bin/syno_pstore_collect: not found
:: Starting scemd
[ 43.010000] eth0: link down
[ 43.010000] eth0: link up, full duplex, speed 1 Gbps
:: Starting services in background
Starting findhostd in flash_rd...
Starting services in flash_rd...
Running /usr/syno/etc/rc.d/J30DisableNCQ.sh...
Disable ST1000DM003 NCQ
[ 43.240000] EXT4-fs (md0): barriers disabled
[ 43.260000] EXT4-fs (md0): mounted filesystem with ordered data mode
Disable ST1000DM003 NCQ
Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
:: Loading module usb-storage[ 43.630000] Initializing USB Mass Storage driver ...
[ 43.630000] scsi6 : SCSI emulation for USB Mass Storage devices
[ 43.660000] usbcore: registered new interface driver usb-storage
[ 43.660000] USB Mass Storage support registered.
... [ OK ]
============ Date ============
Sat Mar 1 17:25:16 UTC 1930
==============================
starting pid 1757, tty '': '/sbin/getty 115200 console'
Sat Mar 1 17:25:17 1930
DiskStation login: [ 46.090000] EXT4-fs (md0): barriers disabled
[ 46.110000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 46.240000] EXT4-fs (md0): barriers disabled
[ 46.260000] EXT4-fs (md0): mounted filesystem with ordered data mode
[ 48.700000] scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 48.710000] scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 9910 PQ: 0 ANSI: 0
[ 48.750000] sd 6:0:0:0: [sdq] Attached SCSI removable disk
[ 48.820000] sd 6:0:0:1: [sdr] Attached SCSI removable disk
[ 110.380000] synobios: power button pressed, ret = 0
[ 111.640000] EXT4-fs (md0): barriers disabled
[ 111.650000] EXT4-fs (md0): mounted filesystem with ordered data mode
The system is going down NOW!
Sent SIGKILL to[ 112.820000] md: md0 in immediate safe mode
all processes
[ 112.820000] md: md1 in immediate safe mode
Unmounting all file systems.
Unmounting /proc/bus/usb ...
Unmounting /sys ...
Unmounting /dev/pts ...
Unmounting /dev ...
Failed to umount /dev, 16
Unmounting /tmp ...
Unmounting / ...
Unmounting / ...
All file systems unmounted.
rmmod usb_stora[ 117.890000] usbcore: deregistering interface driver usb-storag e
ge
Requesting system poweroff
[ 122.040000] md: stopping all md devices.
[ 122.040000] md: md1 switched to read-only mode.
[ 122.070000] md: md0 switched to read-only mode.
[ 123.070000] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 123.100000] sd 1:0:0:0: [sdb] Stopping disk
[ 123.460000] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 123.480000] sd 0:0:0:0: [sda] Stopping disk
[ 124.090000] xhci_thread. exit!
[ 124.100000] Power down.
[ 124.110000] eth0: link down
[ 124.110000] eth0: link up, full duplex, speed 1 Gbps
[ 124.120000] eth0: link up, half duplex, s
