Hey. Habe die "tote" Platte (Disk1) getauscht. Aber die Meldung ist leider immer noch da.
Kannst Du mal bitte die Smart Werte gegenlesen ?
Hier von der "neuen" Platte. 8 Stunden nach inbetriebnahme:
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf
Device Model: ST12000VN0007-2GS116
Serial Number: ZJV2VCTF
LU WWN Device Id: 5 000c50 0b375501e
Firmware Version: SC60
User Capacity: 12,000,138,625,024 bytes [12.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Feb 23 00:59:26 2025 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 567) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1118) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VA LUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 07 8 064 044 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 08 8 088 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 10 0 100 020 Old_age Always - 8
5 Reallocated_Sector_Ct 0x0033 10 0 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 07 6 060 045 Pre-fail Always - 0
9 Power_On_Hours 0x0032 09 7 097 000 Old_age Always - 3114
10 Spin_Retry_Count 0x0013 10 0 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 10 0 100 020 Old_age Always - 8
187 Reported_Uncorrect 0x0032 10 0 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 10 0 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 05 6 053 040 Old_age Always - 44 (Min/Max 40/47)
192 Power-Off_Retract_Count 0x0032 10 0 100 000 Old_age Always - 97
193 Load_Cycle_Count 0x0032 10 0 100 000 Old_age Always - 134
194 Temperature_Celsius 0x0022 04 4 047 000 Old_age Always - 44 (0 22 0 0 0)
195 Hardware_ECC_Recovered 0x001a 00 7 003 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 10 0 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 10 0 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 20 0 200 000 Old_age Always - 0
200 Pressure_Limit 0x0023 10 0 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 10 0 253 000 Old_age Offline - 3094h+15m+48.642s
241 Total_LBAs_Written 0x0000 10 0 253 000 Old_age Offline - 31694041413
242 Total_LBAs_Read 0x0000 10 0 253 000 Old_age Offline - 13148217985
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ich versuche gleich mal deinen Lösungsansatz.
